Back to guides

Focus Mode on One Tap: An NFC Tag for Your New Year Routine

One tap on a tag can switch an iPhone Focus on and off. Here is how to build it with Shortcuts, where to stick the tag, and what to do when it misbehaves.

Published

Introduction

Yes, one tap on an NFC tag can switch an iPhone Focus on or off. You build it in the Shortcuts app as a personal automation with an NFC trigger and the Set Focus action, and the tag itself can be a blank sticker.

New Year resolutions about less scrolling tend to fail at the first step: opening Control Center and picking a Focus takes just enough effort to skip. A tag stuck to your desk or nightstand turns that step into a physical habit. You sit down, tap, and the phone goes quiet.

This guide covers what you need, the exact build steps, how to make it run without a prompt, where to put the tag, and what to check when nothing happens.

Quick answer

Open Shortcuts, go to the Automation tab, create a new automation, and choose NFC. Scan your tag and name it. Add the Set Focus action, pick your Focus, and set it to Toggle so the same tag turns it on and off. Choose Run Immediately if you don't want a confirmation each time.

One detail that surprises people: the automation only uses the tag's unique ID. It doesn't read or need anything stored in the tag's memory.

What you need

  • An iPhone that reads NFC tags. Most recent models do. If you're not sure about an older or hand-me-down phone, see which iPhones read NFC tags.
  • One NFC sticker tag. Cheap packs are fine. A 2022 9to5Mac walkthrough put tags at under $10 for a pack of 12, and prices vary by seller.
  • The Shortcuts app, which comes with iOS.
  • A Focus you've already set up. Go to Settings, then Focus, and check that the one you want (Work, Sleep, Do Not Disturb or a custom one) lists the people and apps you want to allow.

How you switch a Focus today

Apple's own paths are Control Center (tap Focus, then the one you want), Settings, then Focus, or asking Siri, for example "Turn on the Work Focus". Tapping a new Focus turns the previous one off.

Apple also lets a Focus start itself on a schedule, at a location or when you open an app, and Smart Activation can suggest turning one on from your habits. Those work well for predictable routines. A tag covers the moments no schedule predicts: a work block that starts when you sit down, or a wind-down that starts when you decide it should.

Build the automation in Shortcuts

Step 1: Create the NFC trigger

  1. Open Shortcuts and go to the Automation tab.
  2. Tap the plus button to create a new personal automation.
  3. Choose NFC.
  4. Tap Scan and hold the top of your iPhone to the tag.
  5. Give the tag a name you'll recognize, such as "Desk Focus".

Step 2: Add the Set Focus action

  1. Continue to the actions and create a new shortcut.
  2. Add the Set Focus action.
  3. Pick the Focus you want to control.
  4. Set it to On, Off or Toggle.

Toggle is the best fit for a single tag. The first tap switches the Focus on, the next tap switches it off. If you'd rather have separate behaviors, make two tags: one set to On and one set to Off.

Step 3: Decide how it runs

You get two choices. Run After Confirmation shows a prompt on every tap, which defeats the point of a one-tap habit. Run Immediately skips the prompt, and you can still turn on a notification if you want proof it fired.

Apple's Shortcuts guide says some personal automations can run without asking, and it lists NFC among them. It also warns that you may need to set individual actions to run automatically too, so if a prompt keeps appearing, check the action as well as the automation. For a second tap-driven build that works the same way, see the midnight countdown automation.

Step 4: Test it

Tap the tag. Swipe into Control Center and confirm the Focus is on. Tap again and confirm it switched off. Try it once with the screen unlocked and once with the phone locked, so you know what happens when you reach for it half awake.

Where to put the tag

Put the tag where your hand already goes.

  • Desk edge or monitor stand for a work Focus. Tap as you sit down.
  • Nightstand for a Sleep or Do Not Disturb Focus. Tap as you put the phone down for the night.
  • Kitchen counter or study table for a reading or homework Focus.

Metal under a tag can weaken the signal. If your desk or stand is metal, use a tag made for metal surfaces or add a spacer. Also, make one automation per tag: a desk tag for Work and a nightstand tag for Sleep are two separate automations, each with its own scan.

Common problems and fixes

Nothing happens when you tap. Move the phone slowly across the tag. The reader is near the top of the iPhone, and a thick case or a wallet in between can block it. Then check in Shortcuts that the automation is switched on.

It asks for confirmation every time. The automation is probably still set to Run After Confirmation. Switch it to Run Immediately and check the Set Focus action too.

The wrong Focus is active afterward. A Focus switched on by another trigger, such as a schedule, can replace the one you toggled, because tapping a Focus turns the previous one off. Keep schedules and tags for different Focus modes, or you'll end up fighting yourself.

You got a new phone. Automations live on the phone, not on the tag. The tag will still scan, but you'll need to rebuild the automation on the new device. When you do your yearly cleanup, a January tag audit is a good time to check which tags still do something.

Doing this with NFCore

The Focus switching is done by Shortcuts, not by NFCore. NFCore helps around the tag: it can read a tag to confirm the type, and you can write a short text label to it so you remember what it does when you find it in a drawer in March. NFCore doesn't track you, needs no account and doesn't upload anything.

Get it from the App Store or Google Play. Keep in mind that the Shortcuts steps in this guide are iPhone only.

Ideas for your New Year routine

Start with one tag, not five. A desk tag for Work is the easiest to keep, because you already sit down at the same spot every day.

Once that sticks, add a nightstand tag that starts Sleep or Do Not Disturb. If you're also logging a new habit, pair the Focus tag with habit tracker tags so one tap starts the quiet and another logs the work.

Keep the Focus itself simple. Allow the few people who truly need to reach you, silence the rest, and review the list after a week.

Conclusion

One tag, one automation and one Focus is enough to make a resolution easier to start. Build the NFC trigger in Shortcuts, pick Set Focus with Toggle, choose Run Immediately, and stick the tag where your hand already goes. If it works for a week, add a second tag. If it doesn't, the fixes above cover the usual causes.

Frequently Asked Questions

Can one NFC tag turn a Focus on and off?

Yes. In a Shortcuts NFC automation, the Set Focus action can be set to On, Off or Toggle. Toggle lets the same tag switch the Focus on with the first tap and off with the next.

Does the tag need to be written with anything?

No. The automation only uses the tag's unique ID, not what is stored in its memory. A blank sticker works, and you can still write a note on it with NFCore so you know what it does.

Will it run without asking me every time?

You can choose Run Immediately instead of Run After Confirmation. Apple lists NFC among the personal automations that can run without asking. You may also need to set the individual action to run automatically.

Does this work on Android?

The Shortcuts steps here are for iPhone only. Android has its own automation apps, and the idea of tapping a tag to switch a mode carries over, but the menus and actions are different.