New Phone as a Gift? What Happens to Your NFC Tags and Shortcuts
Your NFC tags keep their data on a new phone, but iPhone automations arrive switched off and Android may need NFC turned on. Here is the checklist.
Introduction
Your NFC tags keep working on a new phone, because the data lives on the tag and not on the phone. What you do need to check is the phone side: an iPhone brings your personal automations over switched off, and an Android phone may need NFC turned on before it reads anything.
If a new phone is under the tree this year, yours or someone else's, here's the short checklist for NFC tags on a new phone. It covers what carries over, what doesn't, and how to get every tap working again in a few minutes.
What lives on the tag and what lives on the phone
It helps to split your setup into two halves, because they behave very differently when a phone changes.
The tag keeps its own data
An NFC tag is a passive chip. A tag such as an NTAG213, NTAG215 or NTAG216 gets both its data and its power over the 13.56 MHz contactless link from whatever phone you hold against it. NXP's product documentation for those chips lists an operating distance of up to 100 mm and a rated EEPROM data retention of 10 years under datasheet conditions. No battery to swap, nothing paired to your old phone.
So the URL, text, Wi-Fi record or contact card you wrote to a tag is still there. A new phone reads the same NDEF record the old one did. You don't need to rewrite anything just because the hardware changed.
The phone holds the reactions
Everything that happens after the tap is phone-side: the Shortcut that turns on a lamp, the automation that starts a timer, the app that opens a link, and the permission settings behind them. Those are the pieces that can go missing or stay switched off after a move.
iPhone: personal automations come over switched off
This part surprises people most. You set up an iPhone so that tapping a tag runs a Shortcut, you move to a new iPhone, and the tap does nothing.
What Apple says
Apple's Shortcuts documentation says that automation shortcuts are specific to a device. The automation is backed up to iCloud, but it comes across to other devices with the automation disabled. Apple's page on syncing shortcuts repeats the point: personal automation shortcuts are disabled by default during sync.
Apple's two pages word it a little differently (one says backed up and synced disabled, the other says disabled during sync), but the practical result is the same. Expect to switch each one back on by hand.
Apple's Quick Start page says that when you restore from iCloud, your apps and data download in the background so you can start using the new phone right away. That page does not list Shortcuts automations by name, so don't assume they'll arrive ready to run.
How to switch them back on
- On the new iPhone, open Settings, tap Shortcuts, and check that iCloud Sync is on.
- Open the Shortcuts app and tap the Automation tab.
- Tap each automation, including the ones that start from an NFC tag, and turn it on.
- Run a test tap for each one.
Apple lists NFC among the triggers that can run automatically, and notes that you may also need to set individual actions to run automatically. By default an automation asks you before it runs: you get a notification and tap to confirm. Some personal automations can be set to run without asking, in which case they will not notify you when they fire. If an automation seems to wait for you, check that setting, and look at Privacy inside the shortcut for Allow Running When Locked.
Android: check that NFC is on
On Android the tag side is the same, and the phone side is usually shorter. The one thing to confirm is that NFC itself is switched on.
Google's Pixel help page gives the path: open Settings, tap Connected devices, then Connection preferences, then NFC, and turn on Use NFC. The same page warns that turning NFC off also turns off other features that use it, so a phone with NFC off won't read your tags at all. Other makers label the menus differently, so if you can't find the setting, search your settings for "NFC". If there is no NFC setting anywhere, the phone does not have NFC hardware.
Android phones differ from iPhones in what they can read and write, so a tag that behaved one way on your old phone may behave slightly differently on a new one from another brand. Our iPhone vs Android tag reading chart shows where the two platforms differ.
Re-test every tag on the new phone
Once NFC is on and your automations are enabled, do one pass over everything you own. It takes less time than you'd think.
- Tap each tag once and note what happens.
- If nothing happens on an iPhone, go back to the Automation tab and check that the automation is switched on.
- If a prompt appears where your old phone ran silently, that is the confirmation setting described above.
- If a tag opens the wrong thing, read it with an NFC app to see what is actually stored on it.
NFCore can read a tag and show you its contents, so you can confirm the record is intact before you blame the tag. It works without an account and does not upload anything. Android users can find it on Google Play.
If you are giving tags along with a phone, it also helps to prewrite your tags before gifting, so the recipient only has to tap.
If you are giving the phone to someone else
When the old phone is the gift, wipe it properly. Apple's guidance for selling or giving away an iPhone is to back up the device, sign out, and then erase it. On iOS 26 or later you choose Erase this iPhone or Sign Out But Don't Erase; on iOS 18 or earlier you enter your Apple Account password and tap Turn Off. Then go to Settings, General, Transfer or Reset, and tap Erase All Content and Settings. Apple also says to remove cards and passes from Wallet. Erasing turns off Find My and Activation Lock.
Your tags are not on that phone, so none of this touches them. Keep the tags where they are, and they will read on your new phone the same way. Whoever gets the old phone starts with a clean slate and builds their own automations.
If the recipient is new to NFC, point them to our first-tap walkthrough for gift recipients. One tap that works is the quickest way to make the idea click.
Conclusion
A new phone does not break your NFC setup. The tags hold their data on their own, so nothing needs rewriting. On iPhone, open Shortcuts and switch your personal automations back on. On Android, confirm that NFC is turned on. Then tap each tag once and fix whatever does nothing. If you are giving away the old phone, back it up, sign out and erase it, and keep your tags for the new one.
Frequently Asked Questions
Do I need to rewrite my NFC tags when I get a new phone?
No. What a tag holds is stored in the tag's own memory and powered by the phone's reader field. A new phone just reads the same data. NXP rates NTAG213, NTAG215 and NTAG216 memory at 10 years of retention under datasheet conditions.
Why did my NFC tag stop running my Shortcut on the new iPhone?
Apple says personal automations are specific to a device and come over disabled. Open Shortcuts, tap Automation, and switch each one back on.
Do I have to turn NFC on in a new Android phone?
On a Pixel the setting is Settings, Connected devices, Connection preferences, NFC, Use NFC. Other makers label it differently, so search your settings for NFC. If there is no NFC setting, the phone has no NFC.
Should I wipe my old phone before I give it away?
Yes. Apple's guidance is to back up, sign out, then erase all content and settings. Your tags are not on the phone, so they are unaffected.