Smoke and CO Alarm Test Reminders With NFC Tags
A tag beside each alarm can run a Shortcut that logs your monthly test and yearly battery change. Here is how to set it up, and what it can't do.
Introduction
An NFC tag next to each smoke and carbon monoxide (CO) alarm can open an iPhone Shortcut that logs your monthly test and your yearly battery change with one tap. It doesn't test the alarm for you. It makes the habit easy to keep and easy to check.
Most of us only think about alarms when one chirps at 3 a.m. A tap-to-log tag turns "did we test that this month?" into a quick look at a list. Below you'll find what to log, how to build the tag, where to put it, and a New Year safety log to start the habit.
What a tag can and can't do
A tag stores a small piece of data, usually a link or a text record. When you tap it, your phone does something with that data, such as running a Shortcut. That's it. The tag can't sense smoke or CO, can't tell whether an alarm works, and can't raise any alarm of its own.
The test button itself has limits too. The US Consumer Product Safety Commission (CPSC) notes that a CO alarm's test button checks whether the circuitry is working, not how accurate the sensor is. It also says to follow the manufacturer's instructions. So treat the tag as a logbook that sits beside the alarm, and keep your alarm's manual as the authority.
The routine to log: monthly test, yearly battery, ten-year replacement
Monthly test and yearly battery
The National Fire Protection Association (NFPA) guidance, as summarized in the Wikipedia article on smoke detectors, is to test smoke alarms at least once a month with the test button and to replace batteries at least once a year, or sooner if the alarm starts chirping. A chirp means a low battery on most alarms, so don't wait for the next scheduled change.
That gives you two entries per alarm to log: "tested" each month, and "battery changed" once a year. Check your alarm's manual, because yours may say something different.
Sealed 10-year units and manufactured dates
Home alarms usually run on a 9-volt battery, a sealed 10-year battery, or mains power. With a sealed unit you don't change the battery at all: when it runs low, the whole alarm goes. The same sources say smoke alarms should be replaced after ten years, and that since 1999 Underwriters Laboratories (UL) labeling has required a plain-English manufactured date on every smoke alarm.
So do this once: take each alarm down, read the manufactured date on the back, and write it into your log. Your replacement year is then a number you look up, not a guess.
CO alarms
For CO alarms, don't assume the ten-year figure. CPSC says each alarm has a recommended replacement age, and you can find it in the product literature or get it from the manufacturer. Look it up for your model and log that date instead.
Build the tag and the Shortcut
You need three things: an NFC tag, a phone that can read it, and somewhere to keep the log.
- Pick a tag. Any NDEF-capable sticker works for a link or short text. An NTAG213 is plenty. If the alarm is on a ceiling or near metal, choose a tag made to work on metal surfaces, or put the tag on a nearby wall instead.
- Check your phone. Not every older iPhone reads tags without an app. See which iPhones read NFC tags before you buy a batch.
- Write the tag. In NFCore, write a short text record such as "Hallway alarm" (one per alarm) so each tag has its own name.
- Build a personal automation. In the Shortcuts app on iPhone, tap Automation, create a personal automation, and choose NFC as the trigger. Scan the tag so Shortcuts remembers it.
- Add the action. Have the Shortcut add a line to a Notes file, a Reminders list, or a spreadsheet: the alarm's name, today's date, and "tested". Make a second tag, or a second action, for "battery changed".
Apple's Shortcuts guide says some personal automations can run without asking you for confirmation, controlled in the shortcut's privacy settings, and that individual actions may need to be set to run automatically. Whether you want a prompt is your call. For a log, a quick "Run" confirmation is a useful pause: it means you only record a test after you have actually pressed the button.
If you already track another chore this way, the setup will feel familiar. The furnace filter log uses the same tap-to-log pattern.
Where to put the tags
Put the tag near the alarm, not on top of it, and not where it blocks the vent holes. A spot on the wall below the alarm, at a height you can reach without a ladder, works well. Keep it away from heat and steam.
For alarm placement itself, CPSC advises CO alarms on every level of the home and outside sleeping areas, with interconnected alarms best. It recommends against putting them in kitchens or above fuel-burning appliances, and says to avoid spots near heating vents or where furniture or drapes could cover them. Put the tag where the alarm already is. Never move an alarm to suit a tag.
Give each tag its own name, one per alarm, so the log tells you which alarm was tested. If you want a bigger routine, the idea in one tag per room fits well: the alarm check becomes one item in each room's list.
A New Year safety log
New Year's Day is an easy date to anchor a yearly check. On January 1, you could:
- Press the test button on every smoke and CO alarm and log it.
- Change the batteries in any alarm that uses replaceable ones, and log it.
- Read each alarm's manufactured date and replacement age, and add the replacement year to your list.
- Check that nothing is covering an alarm.
Then log the monthly test on the same day each month, such as the first. If you like tracking habits by tap, tap-to-log habit tags use the same idea for other resolutions.
If your alarm ever sounds a CO warning, don't stop to log anything. CPSC says to move outside to fresh air right away, call emergency services or 911, and not go back in until responders say it is safe. If you're not sure about your setup, ask your local fire department or a qualified technician.
Conclusion
A tag beside each alarm won't make your home safer by itself. It makes the monthly test and the yearly battery change quick enough that you actually do them, and leave a record you can read at a glance. Test each alarm yourself, follow the maker's manual for your model, and replace alarms when they reach their recommended age.
If you want to try it, NFCore on the App Store and NFCore on Google Play can write the tags for you.
Frequently Asked Questions
Does a tag replace pressing the test button?
No. The tag only logs and reminds. You still press the alarm's test button yourself, and the tag can't tell whether the alarm works.
How often should I test and change batteries?
NFPA guidance, as summarized on Wikipedia, is to test monthly and replace batteries at least yearly, or sooner if the alarm chirps. Follow your alarm's manual if it says something different.
When do I replace the whole alarm?
Smoke alarms are advised to be replaced after ten years, and the manufactured date is printed on the alarm. For CO alarms, CPSC says each has a recommended replacement age in its product literature or from the maker.
What if my CO alarm sounds?
Get outside to fresh air, call emergency services, and don't go back in until responders say so. Don't stop to log it.